KnitPro Knit Blockers 2 sizes - 20 pcs

KnitPro Blockers 2 sizes are for you who crochet or knit a lot and have problems with the project pattern not becoming clear enough or the project losing shape after washing. If that's you, then KnitPro Blockers 2 sizes are the way to go.

KnitPro Blockers 2 sizes a pack of 20 blockers for blocking home knitted and crochet projects. You block projects to open patterns and make projects even more beautiful. You also block to get the right shape on the project, for example when it has been washed. Blocking is very simple. You start by spreading out the damp project on blocking mats that are the right size for your project. If you don't have blocking mats, you can find them here. Then you simply take your new blockers and attach the project to the mat in the shape you want it. It's that simple.

KnitPro Blockers 2 sizes work much like T-pins, but provide greater stability and uniformity in blocking, making it easier and faster for you. Each blocker has 4 or 8 pins, which are what hold the project in place. This means that with one movement you can put in 4 or 8 needles at the same time, where with T-pins you have to put in each one individually. For larger projects or projects with long sides, KnitPro Blockers are perfect. But you can also use them for projects with a wavy or detailed edge, for example.

The pack contains two sizes of blockers. There are 12 blockers with 8 pins and 8 blockers with 4 pins. This gives you the pins and sizes you need for any project. The large blockers measure approximately 7.2 cm in length, are 0.5 cm wide and measure from top to pin tip approximately 4.5 cm. The smaller blockers measure approximately 3.6 cm in length, are 0.5 cm wide and also measure approximately 4.5 cm from top to needle tip.

The blocks are made of strong plastic and the needles are made of stainless steel. This makes for good, durable blockers that won't break or rust when they come into contact with wet crochet or knitting fabric. The needles are very sharp, which makes it easy for you to attach them to the blocking mat.

The blocks have two holes at the bottom of the plastic part, which can be used to insert yarn all the way down the row of blockers while they are in use, so you can achieve the same pressure and pull throughout the project.

KnitPro Blockers 2 sizes come in a smart, small and purple plastic box. At the bottom, there is a foam mat that the spm blocks stick to. Grooves in the sides of the box make sure the blocks stay in their places, making it easy for you to get them all back in place when you're done. The box also includes instructions for use. The instructions are in English and German, but we've made a translation for you below.

KnitPro is known for using the best materials for their products to give you, the customer, the best result. Before selling the products, KnitPro also gets them tested by seasoned crocheters and knitters from all over the world to make sure the products work as they should, are comfortable to work with and last long. So you're guaranteed great products with KnitPro.

Specifications

• KnitPro Blockers 2 sizes - 20 pcs
• Material: stainless steel and plastic
• Size: 7,2x4,5x0,5 and 3,6x4,5x0,5 cm
• Color: white
• Contents: 12 blockers with 8 pins, 8 blockers with 4 pins, instruction manual, storage box

Instructions

Knit or crochet your project as usual. Soak your finished project in tap water for about 30 minutes. Squeeze out some of the water with your hands without wringing. Spread the project out on the blocking mat. Use the blocks at the edge of the project by pressing them through the project and into the mat.

For straight edges, place the blocks about 7.5 cm apart or closer together, depending on the project.

For projects with detailed edges (e.g. wavy, jagged), you can use the holes in the blocks to make a straight edge you can start from when blocking. Measure a piece of yarn to about 1.5 times the length of the side you want to block and tie it into a hole on a small blocker. Attach this blocker to a corner of the project and secure it to the mat. Thread the other end of the yarn onto a needle and pass the needle with the yarn through the edge of the side of the project (e.g. at the tips of the branches). Stop when you reach the corner. Loosely attach this end of the yarn to another small blocker and the blocks for the project and mat. Keep the yarn loose until you have laid the project out so it is straight. Then tighten the yarn and attach it to the blocker. You can now put the blockers in the project along the straight line of the yarn and get a stringy result.